
It is the last week of October, and the distribution centre manager is walking the floor with a coffee in one hand and a clipboard in the other. Volumes are already climbing. In three weeks the extra night shift starts, and by early December the yard will be full of trailers waiting for a dock.
Reach truck 4 is parked against the wall with a handwritten note taped to the mast: “Hydraulic leak, waiting for tech.” The note is dated 2 October. Two counterbalance trucks are due for their load tests next month. And the rental company has just mentioned, very politely, that spare units for December are “going fast”.
Nobody has done anything wrong. The fleet was simply prepared for an ordinary month, and the next two will be anything but.
Peak season exposes the fleet you already have
Busy periods rarely create new fleet problems. They expose the ones that were already there: the truck with the intermittent fault, the service that kept being moved to next week, the battery that no longer quite lasts a shift. In a quiet month these are irritations. When every machine is needed on every shift, they become late loads and unhappy customers.
The difficulty is timing. Once volumes peak, there is little room to take a machine out for planned work, technicians are stretched across all their customers and hire units are harder to find. The real window to prepare is the few weeks before the rush, which is exactly when everyone is busy planning labour, stock and transport.
That makes forklift readiness easy to postpone. A simple peak season forklift checklist helps, because it turns a vague worry into a short list of things that can be checked this week.
Start with an honest count of what can actually work
The first question is not how many forklifts the site has. It is how many can be relied on for a full shift, every shift, from mid-November to the new year.
Those two numbers are often different. The asset register might show twelve trucks. In practice, one is waiting for parts, one has been lent to another site, one is booked for a load test and one is “fine, as long as you don’t lift above the third beam”.
Go through the fleet machine by machine and sort each one into three groups: ready, needs work before peak and not available. Be strict. A truck that only behaves when one particular operator drives it is not ready.
Clear the overdue list before volumes rise
Next, look at everything that is due or overdue: planned services, inspections, load tests and the repairs noted on earlier job cards but never booked. Anything falling due in December is worth bringing forward while the operation can still spare the machine.
This matters for more than reliability. An inspection or load test that expires in the middle of peak leaves the site with an awkward choice between parking a machine it badly needs and running one whose records are out of date. Neither is a decision anyone wants to make at two in the morning on a busy night shift.
Small findings deserve attention too. A worn tyre, a weak horn, a seat switch that sometimes fails. These are quick fixes in October and avoidable breakdowns in December.
Batteries and chargers need their own check
Electric fleets have an extra question to answer: will the batteries cope with longer shifts? Peak often means more operating hours and less time on charge, so a battery that just about manages a normal shift may not survive an extended one.
Check which batteries are tiring, which chargers are giving trouble and whether the charging routine still works once shifts are longer. If spare batteries or a revised charging rota are needed, those decisions are far easier to make now than in the second week of December.
Agree the breakdown plan before the first breakdown
However well a fleet is prepared, something will break. What matters then is how quickly the site can get the machine back to work.
Before peak, confirm the basics with each service provider. Who should breakdowns be logged with, and how? What response does the agreement actually promise, and does it cover nights and weekends? Which parts for the most-used machines are likely to be in stock, and which would have to be ordered?
The same applies to rental. If extra units will be needed, book them early and be clear on the rental period, the equipment schedule and the terms. A hire unit that arrives without anyone recording when it is due back has a habit of becoming a very expensive permanent resident.
Where FMC supports peak season readiness
FMC is designed to keep this kind of preparation visible, rather than spread across notes, inboxes and memory. FMC Service Management helps teams plan recurring services, inspections and load tests, capture breakdown callouts and see which jobs are planned, allocated, in progress, delayed, awaiting action or completed.
FMC Contract Management keeps SLA commitments, rental periods, equipment schedules and agreed terms in one record, so the answer to “what does our agreement actually say?” isn’t buried in an email from last year. For fleet customers running several sites, FMC brings assets, service activity, suppliers, compliance and costs into one view.
The software keeps the information in sight. Deciding which machines to fix, rent or rest still belongs to the people who run the operation.
A peak season checklist for the next two weeks
If your busy season is close, these questions are a sensible place to start:
- How many machines are genuinely ready for full shifts, and which are not?
- Which services, inspections or load tests fall due before the new year, and can any be brought forward?
- Which repairs have been noted on job cards but not yet booked?
- Are batteries and chargers fit for longer shifts?
- Who logs a breakdown, with whom, and what response has been agreed for nights and weekends?
- Are rental units booked, and does everyone know when each one is due back?
None of this takes long. Most of it is a walk around the floor and an honest conversation with your service provider.
Peak season rarely breaks a fleet. It shows you what was already broken, so find it in October rather than December.

